• 목록
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your Fiat 500 Key Fob Won't Work

A key fob from fiat key duplication 500 allows you to easily open doors and start your vehicle. However, there are many reasons the fob could stop working. This includes a dead battery, water damage, issues with the receiver module, and interference.

This listing is for a NEW replacement Fiat Flip Key Remote that appears similar to the Ilco brand. It must be professionally programmed (click here to find local locksmiths in the automotive industry). It comes with trunk, lock and unlock buttons.

Dead Coin Battery

A dead battery is the most common cause of your 500 key fob not functioning. Modern key fobs only have an operating range that is limited and must be within just a few inches of the vehicle to work. If you're not close to your vehicle when you press the key fob button the car won't respond, and will display a "Key Fob Not Detected" message in the instrument cluster.

If this happens, replace the coin cell battery (Part number CR2032) by a new one from a reputable manufacturer like Panasonic, Duracell, fiat 500 car Keys or Energizer. They are usually available at your local hardware store, or fiat 500 Car keys online.

You can test the coin-cell battery by pressing the buttons while you're standing close to your Fiat 500 Car Keys 500. The car will flash its parking lights and the key fob should operate the lock and unlock switches.

If your key fob doesn't work even after replacing the battery, there could be water damage that prevents it from communicating with the module inside your vehicle. Water damage can occur in a variety of ways, such as simply splashing or submerging the key fob into saltwater at the beach. If you suspect that your fob was exposed to water, place it in a bag of rice to draw out the moisture. If this does not work, you'll have to get your fob replaced by an auto locksmith or dealer.

Water Damage

Water damage can occur if you submerge the fob in the ocean or wash it in a washer. Saltwater can cause the circuit board to become shorted and eventually die. It's not good to get the fob wet however, don't give it up if you accidentally drop it in the water or don't remove it from your pants pocket.

First, remove the battery. Before replacing the battery, clean the electronic chip using isopropyl or similar products. Check the fob to check if it's functioning. If the key does not function, it may need to be changed. This is usually handled by an auto locksmith or dealer.

If the key is more recent and was not programmed to your vehicle it is likely to need to be replaced completely. A professional automotive locksmith will be able to complete this process. The locksmith will need the key cut to match your car's ignition. The locksmith will also need to reprogram the fob into the vehicle's system. This is a quick and inexpensive process that is usually completed within the next day.

Receiver Module Issues

One of the simplest reasons why your 500 key fob could stop functioning is that it's out of range. The remote typically has an area of 30 feet or less and if it's far away from your car it will not respond to your commands. It can be solved by moving closer to your vehicle until it begins responding.

If your fob does not work after you replace the battery inside the coin, which is also known as a "button", "watch" or "button" It may be due to a malfunction on the internal circuit board. Reprogramming the fob is usually the solution to the issue. You can find directions on how to do this for the majority of automobiles by searching YouTube or looking through the owner's manual.

You may need to replace the metal retaining clips that keep the battery of your coin in place. If they loose tension it could hinder the battery from being seated properly and can cause your remote to malfunction.

In rare cases it is possible that the fob will become desync'd with your vehicle due to software problems or hardware issues. This could cause a significant trouble, but you could often fix this by visiting an auto locksmith to reprogram your fob for you. In some instances they may have to reinstall the program in your body control module too.

Interference

Interference can also cause the key fob to not be able to receive or transmit a signal. This could occur if the key fob is in close proximity to a radio transmitter like a cellphone or radar detector. Other reasons why the key fob might not function may be a lack of connection to the buttons, damage to the internal chip, or water damage.

If the key fob failed to work one day out of the blue or even after trying everything you can at home to resolve it e.g. You could have a malfunctioning 500 receiver module in the event that you've tried replacing the battery, reprogramming, and using an alternative key fob. The receiver module, which is located under the dashboard, picks up radio frequency signals from your key fob. It converts them to electronic commands that the vehicle interprets.

There is a straightforward method to reset the 500's on-board system including the keyfob. Disconnect the battery for 15 minutes by taking off first the negative cable and then the positive cable. Reconnect the battery. This will clear any residual electric current, and also restart the computer in your car. This can help you get your key fob to function again. If the problem persists you should speak with an expert certified technician. They will be able to identify the root cause of your problem.