• 목록
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Door Repair - Simple Fixes You Can Do in a Few Easy Steps

It's easy for people to believe that a door cannot be fixed, but there are many easy fixes that can make a huge impact. Let's begin with shifting.

To shim a door, open the door and push it firmly against the frame. Use the block or jack plane to remove small pieces of wood from the binding points.

The Frame

The door frame is an important part of your home. It is essential for the security of your home since it protects against water damage. But it is also prone to being damaged. Door frames can be damaged by bad weather or burglaries, or simply normal use. When they do, it could lead to large gaps, weak latching and an unsightly appearance. Repairing your door frame can be accomplished in just a few steps.

First, remove the trim or molding from around the opening. You can use a hammer an axe, or a power saw to take off the trim. After the trim is removed, make a note of the measurements and replace it after the repair.

The next step is to check the door frame for areas that are decayed or damaged. If you discover any rotten wood, you'll have to replace it. They are typically found at your local hardware store and should be made from a material that matches the rest your door frame. It is recommended to avoid using pressure-treated wood since it has a tendency to warp and twist over time.

After you have replaced any rotten sections of the frame, you will have to ensure that it is secure in the right place. A good way to achieve this is using an shim. It is essentially a piece wood that is placed between the frame and the wall. The shim can provide additional support for the frame, and also prevent it from moving.

After you have replaced any shims, it is an ideal idea to caulk around the door's frame and sill. This will help stop future water damage and also protect the frame from insects.

Then, you'll need to reinstall the trim on your door frame. If you are lucky, repair your old trim might be in decent condition and you can simply nail it back into place. If not, you might require a new trim and follow the same process.

The Threshold

A threshold for a door is the piece of wood that covers and seals the gap between the door and floor. It also stops snow and water from accumulating in the entrance. While it is an important part of the door, a well-installed threshold can also be a gorgeous accent that adds to your home's curb appeal. It's time to replace your threshold if it is damaged, worn out, or scratched. Installing a new threshold not as simple as sliding it under the casing before nailing it into place it must be supported by strips of wood, called shims. They are placed between the frame's two jambs.

To remove the threshold first, cut it away from the edges of the door frame with a circular saw (use a carbide blade, if possible). If you are able take out the sub sill - the frame part which runs below the threshold. If it's rotting, replace it in the same way you replace the threshold.

Use a carpenter’s square to trace the layout lines prior to cutting the threshold. Make note of the right angles for the notches that are able to fit around jambs. You can also buy thresholds pre-cut to the dimensions of your doorway in a home center.

Install the shims, making sure to place them equally. If necessary, you can change the thickness of the shims. However, they should not be larger than 1 1/2 inches. It could require some trial and error to can get the threshold to be just right, but still able to move freely.

Check the fit of your new threshold by closing the door and testing how well it closes and opens. There shouldn't be any daylight under the door and the sweep at the bottom of the doors should be lightly rubbing the top of threshold.

If the threshold fits perfectly but requires a little more support, apply construction adhesive to the shims before pressing them down under the threshold. Repeat the process with additional shhims until you have a snug fit that can withstand weight.

The Hinges

Over time, door hinges rust and deteriorate. This makes it difficult to close the doors. It is essential to fix the hinge so as to secure and close the door in a proper manner. If you are replacing the hinge, be sure to use a similar one that is an excellent match in terms of size and shape. You should also make sure that the hinge is placed in the mortise.

First, check the hinge for looseness. If the hinge is not tight it will likely to be snagged to the frame of the door and rub against its strike plate. Look for scratches in the paint or indentation on the frame to determine the location where the hinge is rubs. If the hinge isn't sufficient tight then tighten it up using the help of a screwdriver. If the hinge is still loose, you can try using a sliding shim between the door Window Glass Replacement frame and the hinge, or you may require replacing it completely.

If the issue is that the knuckles on the hinge (the cylinders that the hinge pin is fitted) are bent and need to be straightened, you'll have to straighten them so that they point toward the latch jamb. You can bend the knuckles with the help of a large pair of tongue and groove pliers, or a reversible wrench. It's best to do one at each time, to ensure that you don't bend the hinge leaf.

You might also notice that the hinges on your doors are loose because the screws that hold them in place have been stripped. If this is the situation you could replace the screws to give them a better grip on the hinges.

If the hinge isn't damaged and the screw holes are in good condition you can use a syringe to inject carpenter's adhesive into the hinge mortise and joint. Then screw the hinge into position, and then fix it with the screwdriver or drill. Note the locations of the pilot holes on the door and door and window frame prior to installing new windows hinges. This will allow you to ensure that the screws are placed exactly in the same place as the hinges that were previously installed.

The Hardware

Many people don't think about door knobs, levers and locksets until they stop working properly. Most of these components are repairable. It is usually a simple matter of selecting the best piece that will match the style and finish on your house, and then installing it. It's a good idea, especially for exterior doors, to add weather-stripping.

You might be able to resolve the problem of a door difficult to open by lubricating your lock assembly. Many hinges, handles and locks may become stuck when their wear surfaces get dry or dirty. Cleaning these parts and keeping them lubricated is a cheap windows method to ensure they are operating correctly.

Some of the most common issues with door hardware are broken or loose handle screws, a lock which won't turn on its own when you use hinges that make a sound or squeak. In most instances you can tighten these screws or replace them completely. However, in certain situations, it's better to remove the handle or lock from the door and then sand the spindle, lock cylinder bore hole, and escutcheon holes to ensure they're clean prior to installing new hardware.

If doors are difficult to close, you may need to grease the locking mechanism with penetrating oil. You can clean and replace hinge pins with longer screws to fix squeaky doors.

If you're replacing a handle, lock or hinge, be sure that the one you choose is compatible with the hole size of your door and jamb. This information is typically found on the packaging or manufacturer's website. For example, doorknobs or levers require holes that have specific in its spread (the distance from the center of the hole in the lock to the knob). Check the backset to determine whether the window glass replacement (Bbs.now.qq.com) fits.