• 목록
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

Change of the door lock is an easy and inexpensive method to increase your home's security. This isn't for everyone. It requires some expertise and perseverance.

You need to replace the cylinder that is located within the knob's body. The cylinder is what recognizes the key when it is inserted into the lock.

Take off the lock that was previously used.

The first step is to remove the old lock. It is a fairly easy process, but it is important to keep certain things in your mind. Make sure the new lock fits your door. This will ensure it is secure and upvc door lock replacement doesn't create a gap around the deadbolt or latch.

After removing the latch plate, you will need to look for two bolts or screws in the casing's interior which are holding the casing together with the two halves of the lock replacement near me. Unscrew them using a screwdriver, then pull the lock out of the door. If you are using a mortise locking system there is an anchor screw that connects the handle to the spindle. Use a screwdriver to remove this screw, then pull out the doorknobs.

You must also take the deadbolt and latch plug from the hole in the door jamb. Install the new lock. If you are replacing a upvc door lock a mortise lock, you should also measure the distance between the lock case and the edge of your door to ensure that the new lock will be able to fit.

Several reasons might prompt you to change the door lock, such as being concerned that someone else may have the key or if you're welcoming an incoming roommate. In any event, you can save money by taking the lock off yourself, rather than hiring an expert to remove it. It's much simpler than most people imagine and can be done in a matter of a few minutes.

Remove the handle and trim of your door. With a flat screwdriver, take off the trim. You will be able twist off the majority of it and in certain cases, the handles might come off entirely. The next step is to look for a pinhole on the inside of the handle and insert a straightened clip into it. This will activate the release mechanism and allow you to take the handle from the door. Look for a small tab in the interior of the lock and press it with a screwdriver that is flat. After the spindle has been removed, you can take off the cylinder and the housing.

Selecting a new locking system

You have many options when it comes to selecting a new lock. Take a look at the various types of locks and select one that is in keeping with the design of your door. Think about the backset (the distance between the edge of the door and the center of the hole in the lock) and the cross bore (small hole along the edge of the door frame). Select a lock that will fit the door thickness and swing.

The American National Standards Institute and BHMA have graded all locks for doors to give you an idea of their longevity and how difficult it is to pick them or disable them. A grade 3 lock may be the best choice for a peaceful rural apartment complex, while an entry grade lock could stand up to the traffic at a busy storefront on a busy city street.

Most smart door locks require digital code to open. If you are worried about hacking, or other security concerns, speak to an expert locksmith.

Replace the cylinder

If your door lock cylinder is broken or damaged you can repair it in just a few minutes using a simple DIY project. The key is to choose the correct cylinder and follow the steps that are included with it. The first step is to remove the handle or knob if there is one then loosen the trim that is attached to the base of the lock cylinder using a screwdriver. Once the trim is removed, you will be able to access the screws that hold the cylinder in place and remove them with a flathead screwdriver. The cylinder can then be gently lifted out of the door.

Be sure to measure the length of the new cylinder prior to putting it in place. With a tape measure, determine the distance between the cylinder's center and its right and left sides. Then, purchase an additional cylinder using the same measurements. This will help prevent cylinder snapping, which can happen when the door is kicked out or when the key gets stuck inside.

If you have a replacement cylinder, place it into the door and turn the key. This will ensure that the cylinder is aligned with the carrier, which is typically located on the outside of the lock. You can then loosen the set screws, which should be only a couple of turns into the head. It is also necessary to loosen the screw at the edge of the door that holds the case in place, if there is one.

You can replace the old lock cylinder with a new one by inserting it into the case and tightening the set screws. The process of reinstalling the component that connects the cylinder to an indicator stem for a lock is also important. This can be done by pulling three small tabs in the back of the cylindrical with needle-nosed pliers. Attach the smaller bracket to the cylinder's back. Then, you should put back in the strike plate and latch plate, as well as the retaining ring that is connected to the top of the lock cylinder.

Installing a new lock

Begin by measuring the width of your upvc door lock replacement window locks (link.Mcmod.cn) if you are replacing an existing lock. Most residential locksets have a thickness of 3/8 to 1 3/4 inches. If your door is more than 1 3/8 to 1 3/4 inches, you'll need an extra thick door kit. This would include longer screws, or an extension for the spindle or a longer the tail piece for door lock repair near me knobs.

Most locks come with detailed instruction booklet to help you install the new hardware. Before beginning, you must read the instructions to ensure you've followed all the steps. The manual will give you a good idea of how much skill is required to finish the task. If you're changing locks for the first time, you might need to seek out an experienced person for help.

It's a great idea to seal the openings of the old hardware prior to installing the new lock. This will keep the screws from slipping out of the holes and protect any tiles you might have installed in the area. It also helps prevent potential damage from rust, dirt, and grime. SECURAM Touch comes with a strip of painter's tape that is intended to be used to protect your painter's tape, but you can also use gaffer's or masking tape if you have it available.

After you have removed the screws that hold the lock's interior to the exterior, take the lock off immediately. This must be done quickly to prevent the lock from closing accidentally and harming the mechanism.

Install the new latch bolt in the upper cross bore of your new lock, if it has one. Make sure that you put it in the correct position that is usually marked by an illustration on the faceplate. Then, slide the latch plate over the bolt and screw it in place.

Attach the deadbolt to the jamb of the door. Test the deadbolt a few times by throwing it to see if it extends into the strike plate. Follow the instructions included in your electronic smart lock to program it. This involves downloading an app, registering your email address, confirming your identity, and then connecting to the wireless network to connect your device.